制造业信息化 / Manufacturing Informatization [ 仿真/ 建模/CAD/CAM/CAE/CAPP]
7 多雷达单目标追踪问题研究 ■ 李中 曹骏飞 石峰
Research on Single-target Tracking Method of Multi-radar
10 基于ANSYS的土壤分层取样装置优化设计研究 ■ 曲芳 李巍
Optimal Design and Research on Soil Stratified Sampling Device Based on ANSYS
13 基于LBM方法的钝体绕流数值模拟 ■ 魏洪桢 谷正气 张勇 等
Numerical Simulation of the Flow around a Blunt Body Based on LBM Method
17 HNC-21TF数控车床自动刀架电气控制系统设计 ■ 贾伟杰
Design of Automatic Tool Turret Electrical Control System for HNC-21TF NC Lathe
20 SiCp/Al复合材料锻造工艺三维有限元模拟 ■ 刘丹 周丽 王唱舟
3D Finite Element Simulation of SiCp / Al Composites Forging Process
22 基于PLC的灯罩旋压机 ■ 张良 杨铁牛 常明清 等
Lampshade Spinning Machine Based on PLC
26 钻具稳定器加工自动编程技术的研究 ■ 徐勇 孙兴伟
Study on Auto-programming Technique in Drilling Tool Stabilizer
28 载荷谱数据分析软件设计与应用 ■ 马相明 孙霞 于华
Design and Application of Load Spectrum Data Analysis Software
31 自动液力变速器行星轮系的预应力模态分析 ■ 赵磊 吴怀超 赵丽梅 等
Prestressed Mode Analysis of Planetary Gear Train of Automatic Hydraulic Transmission Based on ANSYS
34 通过坐标变换建立多关节机器人一般位形方程的方法 ■ 薄纯青 段建中
Establishment of General Configuration Equations for Multi-joint Robot Based on Coordinate
Transformation Method
36 基于LabVIEW的机床声音信号采集与处理系统 ■ 周广林 舒阳欢
Sound Signal Acquisition?and Processing System of Machine Tool Based on LabVIEW
39 基于有限元分析阶梯型复合变幅杆的设计 ■ 刘泽祥
Design of the Stepped Compound Horn Based on Finite Element Analysis
42 减速器输入轴系转子系统不平衡响应分析 ■ 马健 惠升 张海娟
Unbalance Response Analysis of the Rotor System in a Reducer?Input?Shaft Based on ANSYS
45 基于UG的后处理编程研究 ■ 张炜
Research of program Post-processing Based on UG NX
47 基于Adams的无人履带车双流传动系统优化与仿真 ■ 赵耀 孙伟 郑维强 等
Simulation on Double Current Transmissions System of Unmanned Armored Carriers in ADAMS
50 行星齿轮传动系统纯扭转动力学模型的试验验证 ■ 陈云香 李同杰 王娟
Experimental Verification of Pure Torsion Kinetic Models for Planetary Gear Transmission
52 90m自升式海工辅助平台提升齿轮箱行星架强度与疲劳分析 ■ 胡云波 张跃春 吴涛 等
Strength and Fatigue Life Analysis of Planet Frame in Auxiliary Ascending Gear Box of 90m Jack-up Platform for Marine
56 停车设备承重台板架的结构优化设计 ■ 吴任和 康俊远 周铭杰
Structural Optimization of Mechanical Parking System Platen
58 橡胶密封圈加工用工作台动态性能分析 ■ 田杰 李志强 张晔 等
Dynamic Properties Analysis of the Worktable for Machining Rubber Seal
61 基于虚拟样机技术的采煤机截割部运动学仿真 ■ 张宁波
Kinematics Simulation of Coal Winning Machine Cutting Unit Based on Virtual Prototype Technology
62 基于DGUS屏的密码锁功能在PM2.5自动换膜采样器中的实现研究 ■ 程二亭 曹川川
Research and Realization of Password Lock Function in PM2.5 Sampler of Automatic Film Changing Based on DGUS Screen
64 5T冲床自动取送料装置的设计与实现 ■ 张秋容
Design of Automatic Feed & Reclaiming Device in 5T Punching Machine
66 数值模拟技术在拉深模具设计中的应用 ■ 赵灵 周昇
Application of Numerical Simulation Technology in the Design of the Drawing Die
68 基于CATIA的空心齿轮轴有限元分析 ■ 周燕 李小龙
Finite Element Analysis of Hollow Gear Shaft Based on CATIA
69 典型结构件展开的Pro/E解决方案 ■ 苟在彦
Expansion Solutions of the Typical Structure Based on Pro/E
72 基于直线逼近的曲线插补算法研究 ■ 吴新淼
Research of Curve Interpolation Algorithm Based on the Linear Approximation
74 汽车关键零部件精密检测技术研究与应用 ■ 朱秀娟
Research and Application of Precision Measurement Technology in the Processing of Key Auto Parts
76 数控车削椭圆轮廓回转体的宏程序编程技巧与实践 ■ 何全茂 刘晓超
Macro Programming Skills and Practice for Processing the Elliptical Contour Rotary Body on NC Lathe
78 基于MasterCAM的车削自动编程研究 ■ 李月娥
Research on Automatic Programming of Turning Based on MasterCAM
80 一种含隔板涂布干燥导流喷嘴数值模拟与分析 ■ 丁俊健 邱术芹
Numerical Analysis on Clapboard Nozzle’s Velocity and Pressure
82 基于PLC的铁钻工电气系统设计 ■ 朱永庆 罗磊 李峰 等
Design of Electric Control System for Iron Roughneck Based on PLC
84 水冷装置金属软管漏液故障分析与对策 ■ 阮志新 刘一福 李友瑜
Fault Analysis and Countermeasures for Metal Hose Leakage of Water-cooling Device
88 数控钻床提高孔加工效率新方法 ■ 胡彦卓 肖作德 丁天权 等
New Technology for Improving the Efficiency in Drilling Hole on NC Drilling Machine
90 汽轮机高压实心阀体粗加工工艺方案研究 ■ 王治军 白宇光
Research on the Rough Machining Scheme of Steam Turbine High Pressure Solid Valve Body
92 卷筒受力计算方法 ■ 刘顺华 魏军 雒兴刚
Force Calculation Method of Drum
94 基于单片机的单轴控制器的结构研究 ■ 路文斌 林晓海
Study on the Structure of Single Axis Controller Based on MCU
96 矿井井架起吊受力有限元分析 ■ 邢启风
Finite Element Analysis on Lifting Force of Mine Headframe
99 某型直升机用关节轴承安装工装的设计改进 ■ 吕长生 佟勇 卞纪庆 等
Improved Design of Joint Bearing Installation Tooling for a Certain Type of Helicopter
102 某汽轮机末级静叶优化 ■ 王丽华
Optimization of Static Blade in Steam Turbine Last Stage
103 SOG手电筒筒身异形轮廓的数控加工 ■ 许达记
NC machining of the Special Shaped profile of SOG flashlight barrel
105 基于MATLAB的工业机器人3R机械手臂运动学与空间分析 ■ 长丹华
Kinematic and Workspace Analysis of Industrial Robotic 3R Manipulator Based on Matlab

学术交流 / Academic Communication [ 理论/ 研发/ 设计/ 制造]
107 分布式驱动电动汽车悬置系统设计 ■ 熊璐 傅稳
Mount System Design of Distributed Drive Electric Vehicle
110 ROV及外接设备接口研究 ■ 王杰文 齐兵兵 黄佳瀚 等
Research on ROV and Its Special Equipment Interfaces
112 基于ECRS原则与工序重构的发动机装配线平衡问题分析 ■ 赵华丽 严伟 王煜
Analysis of Assembly Line Balancing Problem Based on the Principle of ECRS and Recombinant of Procedure
116 100%低地板齿轮箱设计关键技术探究 ■ 朱万刚
Study on the Key Design Method of 100%LRV Gearbox
118 基于物元分析法的生产系统柔性综合评价 ■ 王屾 房殿军
Flexibility Evaluation of Manufacturing System Based on Matter Element Analysis
121 基于小波变换的自主机器人运动目标检测研究 ■ 贾继红 张健
Research on Detecting Moving Object of Autunomous Robot Based on Wavelet Transform
123 立体光固化成型技术的节材研究 ■ 金嘉琦 宋君峰 孙凤 等
Research of Saving Material Method on STL Printing Technology
126 高g值冲击振动系统的设计与测试研究 ■ 纪亮
Design and Test Research of High g Impact Vibration System
128 光伏电池片生产中排除扩散炉故障的实验研究 ■ 史君
Experimental Study on Fault of Screening Diffusion Furnace in the Production of Photovoltaic Cell
130 热浸镀锌窑炉锌浴温度控制方法研究 ■ 倪洪启 张浩 王树强 等
Study on Temperature Control of Hot Dip Galvanizing Furnace
132 基于计算机单目视觉的刚体位姿测量在直升机飞行驾驶模拟器上的应用
■ 董传福 崔玉鑫 刘哲 等
Application of Computer Mono-vision-based Rigid Body Attitude Measurement in the Helicopter Flight Driving Simulator
133 装甲车辆模块化实验平台总体研究 ■ 王克运 何志刚 关涛
Overall Research on the Modular Experiment Platform of Armored Vehicles
136 激光-电弧复合焊后的高强钢微观组织分析 ■ 张渌洋 黄根哲 魏立林
Microstructure Analysis on Welding Point of High Strength Steel Using Laser-arc Hybrid Welding
138 滚珠丝杠副传动机构的优化设计与研究 ■ 赵少锋 魏敏 周永刚 等
Optimization Design and Research of Ball Screw Transmission Mechanism
140 120t转炉托圈及联接装置热-机耦合应力作用下的变形研究 ■ 杨权
Deformation Analysis of 120t Converter Trunnion Ring and Its Coupling Device under the
Thermo-mechanical Coupling Stress
143 基于摆-球“永动器”的加工工艺分析 ■ 代恒 刘波 谢玄 等
Analysis of Processing Technic Based on Perpetual Motion Machine of Pendulum-ball
145 一种***小间距挑战赛无碳小车的创新设计 ■ 任仲贺 张学东 曾垂源 等
Innovation Design of Carbon-free Car for Minimum Obstacle Spacing Challenge
149 秸秆生物质平模成型机关键部件的改进设计 ■ 鲍昀利 鲍振博 靳登超 等
Improved Design of Key Components in Straw Biomass Plane-die Briquetting Machine
152 无碳小车转向机构设计与微调分析 ■ 陈果 黄荣舟 李炳川
Steering Mechanism Design and Fine Adjusting Analysis of Carbon-free Cars
154 筒式果蔬清洗机的设计研究 ■ 李东
Design of Roller Type Cleaning Machine for Fruits and Vegetables
156 大直径管道切割机 ■ 张慧珍
Small-Diameter Pipe Cutter
157 道路疏通车淤泥挖斗机械结构设计与研究 ■ 徐有军 段华 李聪
Design and Research on the Mud Bucket’s Mechanism of the Dredge Vehicle
159 基于不均衡转向特性的车轮滑移率估算方法 ■ 孙晖云 陈广彦
Wheel Slip Estimation Based on Unbalanced Steering
162 湿式DCT同步器控制研讨 ■ 宋瑞起 翁晓明 祁稳 等
Study on Control of the Wet DCT Synchronizer
165 基于六自由度运动平台液压系统的设计 ■ 雷杰 姜昆鹏 蒋大伟 等
Design of the Hydraulic System in 6-DOF Motion Platform
167 水下应急维修相关设备和技术研究 ■ 叶永彪 黄佳瀚 齐兵兵 等
Related Equipment and Technologies Study for Subsea Emergency Maintenance
170 汽车发动机缸体******加工技术 ■ 吴宏强
High-efficiency Machining Technology of Automobile Engine Cylinder
172 压水堆核电厂阻尼器布置优化研究 ■ 李茂云 王红瑾 徐城杰
Optimal Method of Dampers in Pressurized Water Reactor Nuclear Power Plant
175 建材装备制造企业生产协作和外协管理方法研究 ■ 杨曙运
Research on Production Cooperation and Collaboration Product Manufacturing Management of Building Material Equipment Enterprise

解决方案 / Solution [ 工艺/ 工装/ 模具/ 诊断/ 检测/ 维修/ 改造]
177 农用马铃薯收获机刮泥板支撑座夹具设计的研究 ■ 李蕾 吕江虹 周延昌
Research on Fixture Design for Processing Support Unit of Agriculture Potato Lifter’s Mud Scraper
178 提高人字齿插齿加工对称性的方法 ■ 严红毅 代国辉 邓应诚
Processing Method for Improving the Symmetry of Herringbone Gear
180 热轧精轧机窜辊液压缸故障分析及改进措施 ■ 包国华 张新顺 刘鸿涛 等
Fault Analysis and Countermeasures for Hydraulic Cylinder of Shifting Roller in Hot Finishing Mill
181 永磁铁自吸原理在起重工具设计中的应用 ■ 张锡联
Application of Permanent Magnet Principle in the Design of Hoisting Tool
184 特殊止回阀密封面加工基准面的选取 ■ 张春景 曾瑜 郭强
Selection of Datum Plane for Machining Seal Surface of a Special Check Valve
185 离心压缩机椭圆错位瓦制造工艺改进 ■ 孟东民 王鸿雁 熊学强 等
Manufacturing Technology Research on Ellipsoidal Staggered Pad of Centrifugal Compressors
187 巧用量块检测小径轴的键槽的对称度 ■ 杨建飞 孙银华
Application of Gauge Block in Measuring Symmetry Tolerance of Keyway on Small-diameter Spindle
188 一种齿轮箱从动齿轮轴承退卸工艺分析及改进 ■ 冯自立 代卧龙 梁晓燕 等
Technology Analysis and Improvement of Disassembling Bearing on Driven Gear of Gearbox
190 低合金高强钢焊接在提升设备中的应用 ■ 刘纪超 尹玉刚 张传爽 等
Application of High-Strength Steel Welding in Low Hoisting Equipment
192 一种履带式挖掘机支重轮布置方法 ■ 甄建军 尹彬
Layout Design Method of Crawler Excavator Track Roller
193 YK75系列齿轮成形磨削机床及关键性技术研究 ■ 韩彦科
Research on YK75 Gear Grinding Machine and Its Key Technology
194 全向叉车及其噪声控制 ■ 李冠峰 申勇
Omni-directional Forklift and Its Noise Control
197 超薄大平面加工方法的改进 ■ 李启瑞 耿新生 程永娜
Processing Method Improvement of Ultrathin Large Plane
198 ZB45包装机预切式内框纸输送装置的研制 ■ 张明强 代小军
Study on Conveying Device Pre-cut Type Inner Frame Paper in ZB45 Packaging Machine
200 含Nb低合金高强钢表面裂纹研究 ■ 赵如
Research of Surface Crack on Nb High Strength and Low Alloy Steel
201 机车车体侧墙骨架通用焊接工装 ■ 倪楷
Welding Tooling of Locomotive Lateral Frame
203 快换隔水管母接头焊接用工装设计 ■ 王军
Welding Tooling Design of Quick-change Riser Female Joint
204 基于灰关联度分析大型球轴承噪声的影响因素 ■ 高俊聪 赵景周
Analysis on Influencing Factor of Large Ball Bearing Noise Based on Grey Correlation Degree
206 金属板材坡口切割专用台架的研制 ■ 熊志强 侯丽嫚
Development of the Special Bevel Cutting Platform for Sheet Metal
207 螺杆泵电机直驱齿轮变速驱动装置的研究 ■ 李华成
Research on the Direct-driven Gear Transmission for Screw Pump Motor
209 莲花产品加工技术研究 ■ 陈小欢 蔡霞 魏香林
Study on Processing Lsotiform Workpiece
210 T形板零件倒装式复合冲裁模设计 ■ 林栋
Design of Flip Type Compound Blanking Die for T Shaped Plate Parts
212 振动放矿机漏斗存在的问题及改进 ■ 魏曼玲
Problems and Improvement of Vibrating Feeder Funnel
213 650MW核电汽轮机低压次末级动叶片司太立合金片裂纹缺陷的分析与处理 ■ 葛海华
Analysis and Repair of the Crack on the Second Last Stage Blades Stellite Alloy of 650MWe Nuclear Power Plant Steam Turbine’s Low Pressure Rotor
216 DQLK 600/1000·25型斗轮堆取料机整机主参数的计算 ■ 刘胜
Main Parameters Calculation of Bucket Wheel Stacker/reclaimer
217 供气装置受力分析及强度校核 ■ 胡金磊 蒋娟娟
Stress Analysis and Intensity Check of Gas Distributing Device
219 薄壁件装配焊接技术研究 ■ 李大俭
Erecting Welding Technology of Thin-wall Workpiece
220 三种散热器水室主片定位装置的分析与比较 ■ 邱国佳
Analysis on Three Kinds of Tube Header Plate Fixing Tooling
222 某亚临界锅炉水冷壁泄漏失效分析 ■ 杨权
Failure Analysis of Waterwall Leakage in a Subcritical Boiler
224 一种堆码建材专用起重机 ■ 赵林波 胡广安 曹永梅 等
A Kind of Special Crane for Stacking Building Materials
225 基于声发射技术的储罐无损检测 ■ 张猛
Non-Destructive Testing of Tank Based on Acoustic Emission Technique
227 自动变速箱油泵的设计 ■ 王中华 翁晓明 翟青泉
Design of Automatic Transmission Oil Pump
230 面向GRR的基于PISMOEA模型的GD&T检具设计 ■ 黄祯祥
GRR Reserch of GD&T Gage Design Based on the PISMOEA Model
232 基于负载敏感技术的钻机井口机械化工具的研究 ■ 刘志林 李峰 李亚辉 等
Study on Drilling Wellhead Tools Based on Load-sensitive Technology
235 西门子变频器在石油钻机中的应用 ■ 于雪梅 刘坤
Application of Siemens Inverter in Oil Drilling Rig
236 ZJ17卷接机组新型二次风选装置的改进 ■ 林朝辉
Improvement of New Secondary Winnowing Device in ZJ17 Cigarette Making Machines
238 带压堵漏技术在化工生产中的应用 ■ 李姝 王雪光 高慧
Application of Leakage Stoppage Technology under Pressure in Chemical Production
239 研究梳齿型汽封漏汽问题的流体力学方法 ■ 李书新
Fluid Dynamics Research Methods for Comb-type Steam Seal Leakage
242 道碴给料装置的改造设计 ■ 董干武
Redesign of the Device Loading in Ballast
243 某300MW等级汽轮机启动过程控制 ■ 黄雪
Discussion about Startup Operation of 300MW Turbine
244 某电厂汽轮机组隔板返修方案 ■ 邸强
Repair Plan of Diaphragm in a Power Plant Steam Turbine
246 再制造技术下的采煤机齿轮制造 ■ 丹慧芳
Processing Gear of Coal Mining Machine Using Remanufacturing Technology
248 导弹用气路单向阀密封失效分析和改进 ■ 林乐刚 卢猛 杨美娟 等
Seal Failure Analysis and Improvement Measure for Gas Line Check Valve of Missile
250 无功补偿装置在钻井中的设计与应用 ■ 邵崇权
Design and Application of Reactive Compensation Device in Well Drilling
253 甲烷传感器与轴流风机联动系统 ■ 王芳
Methane Sensor and Axial Fan Linkage System
254 自升式钻井平台升降基础建造工艺介绍和分析 ■ 周莹 李云鹏 景方刚 等
Analysis on Manufacturing Process of the Jackcase Foundation for Jack-up Drilling Unit
257 切削用量对车削加工的影响分析 ■ 安付行
Effect Analysis of Cutting Data on Turning Process
259 原料气压缩机的故障诊断分析 ■ 郭晓宁
Fault Diagnosis of Feed Gas Compressor
261 三销式叶片装配工艺研究 ■ 刘俊峰
Assembling Technology of Three-pin Type Blade
262 基于TRIZ物理矛盾的整包玻璃逐张分离问题研究 ■ 李振锋 闫伟
Study on the Separation of the Whole Package Glass Based on Triz Physical Contradiction
264 PVC穿孔板在通风机中的应用 ■ 李磊 牛朝阳 王魁
Application of PVC Perforated Plate in Fan Machine
265 基于锂电池分容可靠性提高的接触方式 ■ 陈默 韩成祥
Contact Method for Improving Reliability of Lithium Battery Capacity Grading
266 感应钎焊方法进行无铅锡焊的应用 ■ 李宾喜 王曦
Application of Lead Free Soldering via Induction Brazing Method
267 平立转换(H/V)轧机联合减速箱漏油问题的处理 ■ 陈晓
Treatment of Reducer Casing Leakage for Horizontal/Vertical Conversion (H/V) Mill
269 镁合金压铸模具设计的关键技术分析 ■ 李有新 李阳
Key Technology Analysis of Magnesium Alloy Die-casting Die
270 散料料斗干式除尘系统 ■ 唐玉玺 杨大海
Dry Dust Removal System of Bulk Hopper
271 切割机床在叶片加工中应用的可行性 ■ 王文丹
Feasibility Study on Application of Linear Cutting Machine in Blade Machining
273 前车架镗专机多功能技术改造 ■ 牛双敏 丁大状
Technical Transformation of Boring Machine for Processing Front Frame
276 TJ18通井机研制 ■ 李田刚 周莉莉 李湛 等
Design of Tractor Hoist
278 钢丝绳芯胶带输送机减速机冷却降温系统的设计与应用 ■ 王志杰
Design of Reducer Cooling System for Steel Belt Conveyor
279 新型中心喷胶钢管的设计和应用 ■ 崔成福
Design and Application of New Type Glue Spray Steel Pipe